The kit includes: 1 x Arduino Projects Book (170 pages) 1 x Arduino UNO rev.3 1 x USB cable 1 x breadboard 1 x wood base 1 x 9 V battery snap 70 x hard cable 2 x flexible cable 6 x photoresistor 3 x trimmer d10 kohm 10 x push button 1 x temperature sensor 1 x tilt sensor 1 x LCD (16x2i) 1 x LED (white) 1 x LED (RGB) 8 x LED (red) 8 x LED (green) 8 x LED (yellow) 3 x LED (blue) 1 x CC motor 6/9 V 1 x servomotor 1 x piezo 1 x H bridge 2 x photocoupler 5 x BC547 2 x IRF520 5 x 100 nF capacitor 3 x100 ♟ capacitor 5 x 100 pF capacitor 5 x 1N4007 diode 3 x transparent jelly (red, green, blue) 1 x male strip connector (40x1) 20 x 220 ohm resistor 5 x 560 ohm resistor 5 x 1 kohm resistor 5 x 4.7 kohm resistor 10 x 10 kohm resistor 5 x 1 Mohm resistor 5 x 10 Mohm resistor. 15 HACKING BUTTONS: create a master control for all your devices! 14 TWEAK THE ARDUINO LOGO: control your personal computer from your Arduino 13 TOUCHY-FEEL LAMP: a lamp that responds to your touch
EDISON ARDUINO KIT CODE
12 KNOCK LOCK: tap out the secret code to open the door 11 CRYSTAL BALL: a mystical tour to answer all your tough questions 10 ZOETROPE: create a mechanical animation you can play forward or backward 09 MOTORIZED PINWHEEL: a coloured wheel that will make your head spin 08 DIGITAL HOURGLASS: a light-up hourglass that can stop you from working too much 07 KEYBOARD INSTRUMENT: play music and make some noise with this keyboard 06 LIGHT THEREMIN: create a musical instrument you play by waving your hands 05 MOOD CUE: clue people in to how you're doing 04 COLOUR MIXING LAMP: produce any colour with a lamp that uses light as an input 03 LOVE-O-METER: measure how hot-blooded you are 02 SPACESHIP INTERFACE: design the control panel for your starship 01 GET TO KNOW YOUR TOOLS: an introduction to the concepts you'll need to use this kit Once you have mastered this knowledge, you will have a palette of code and circuits to create something beautiful, and make someone smile with what you invent. You will be able to build 15 projects using components that let you control the physical world through different kinds of sensors and actuators. Each Edison PWM can be jumpered to one of three Arduino PWMs.Description: This kit walks you through the basics of Arduino and electronics in a hands-on way. Recommended Reading Writing code for the Edison without using the Arduino IDE is an advanced topic we're going to assume that you're conversant in at least basic Linux command line syntax and C++ syntax. PWM (J11-J12): The PWM headers, also called PWM swizzler, allow the four PWM sources from the Intel Edison Board to be configured to drive four of the six Arduino PWM pins. Edison Hardware Kit - One will be enough to make the Edison/Console/GPIO stack. Make sure the battery is attached with the correct polarity. ICSP (J4): The ICSP header has the same functionality as the ICSP header found it in the Arduino UNO boards.īATT (J2): The BATT header allows attaching a Li-Ion battery for those low-power applications.
EDISON ARDUINO KIT BLUETOOTH
Supports Arduino Sketch, Linux, Wi-Fi and Bluetooth Compatible with Arduino Uno (4 PWM. The jumper is not needed to enable this feature. Intel Edison : Standard Power On Board Antenna + Arduino. To enable this feature tie a 10K thermistor from the NTC pin to GND. This feature can be disabled connecting the NTC pin to GND which is the default position of the NTC jumper as showed in the picture above. NTC (J13): The NTC header allows setting an NTC thermistor input used to monitor battery temperature while charging.
The default ADC voltage reference selected is the IOREF value as showed in the picture above.
When the AREF value is selected, it can be chosen from a voltage range from 0 V to 2.5 V if the IOREF is 3.3 V or from 0 V to 5 V if the IOREF is 5 V. When the IOREF value is selected, it can be 3.3 V or 5 V depending on the IOREF jumper position. The reference can be selected between the IOREF value and an external value on the AREF pin. The default IOREF value selected is 5 V as showed in the picture above.ĪREF (J8): The AREF header allows selecting the ADC voltage reference. IOREF (J9): The IOREF header allows selecting between two voltage levels: 5 V or 3.3 V, to make the IO pins compatible with the level selected. Power supply battery connection, and so on.The Arduino Expansion Board includes several jumper headers to configure the board with different settings such as: Do not finalize a design with this information. The information here is subject to change without notice. The Intel® Edison Kit for Arduino* allows the Intel® Edison Board to be compatible with Arduino shields designed for the UNO R3. Intel® Edison Kit for Arduino Hardware Guide September 2014 Revision 002 Document Number: 331191-002 Notice: This document contains information on products in the design phase of development.
0 kommentar(er)
